Looking for:
Ion dash cam manual |
Ion dash cam manual.Uploaded by
Scan with your Walmart app and let us know what you think. These limits are designed to provide residential protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may interfere with radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Pursuant to Part 15 of FCC rules. Only the cable supplied with the camcorder should be used. Operation is subject to the following two conditions: 1. This device may not cause any harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
Always leave service to authorized repair facilities. Be sure to always keep backup copies of data by transferring to a personalcomputer. In no way will onn or its subsidiaries be responsible for inappropriate use of this product. It is the sole responsibility of the buyer to consult legal counsel for the interpretation of any laws applicable to the area of intended use of this product. Sling Position 2. Micro SD Card Slot 3. Mini USB Port 4.
Reset Button 5. Power Button 6. Button 7. Indicator 8. Infrared LED 9. This battery allows approximately 35 minutes for video recording. The Blue and Red Indicator will illuminate. Then the Red Indicator will turn off. The Blue Indicator will blink.
Then the Blue Indicator will illuminate. If there is no activity for 1 minute, the unit will power off and retain some charge. Then the Blue Indicator will turn off.
The Red Indicator will keep blinking. When finished charging, the Red Indicator will stop blinking and illuminate.
Before first time use, charge it approximately 30 minutes until the unit is fully charged. The unit will power off. Install the Camera Clip to the unit as illustrated below:. Push the Suction Cup on your windshield or any smooth surface then press the Knob on the Suction Cup to lock it as illustrated below:.
Loosen the Plastic Nut by turning it counterclockwise. Adjust the angle of the unit as desired then tighten the Nut by turning it clockwise as illustrated below:. Toremove the mount from the windshield, lift the Knob then pull Cup by the tab on it as illustratedbelow:. Totake out the card or replace new card asbelow: 1. Toremove the card, use your finger to take out the Micro SDCard as illustrated below:.
To reinstall or replace the card. Upload the files to your computer before formatting the card. When the unit is plugged in, it will automatically power on when you start your car.
At this time the Red and Blue Indicators will illuminate and the unit will enter P Video recording mode. When the unit is plugged out or you stall your car, the unit will automatically power off. Mini Action Cam Mode: 1. Recharge the built-in battery, as instructed earlier. The unit will enter Standby Mode. Short press the Button, the Blue Indicator will blink. The unit will start video recording. Short press the Button again to stop video recording.
The Blue Indicator will stop blinking. To power off, press and hold the Button for 6 seconds, the Blue Indicator will blink three times then turn off. The default setting is P. In standby Mode, short press Button to switch between the four Modes. Power on the unit as instructed earlier. The unit is in P standby Mode, the Blue Indicator illuminates. Short press the Button, the unit will start P video recording. Short press the Button again to stop recording, the Blue indicator will stop blinking and illuminate.
Enter P standby Mode as instructed earlier. Short press Button, the Blue and Red Indicator will illuminate. The unit will be in P standby Mode. Short press Button, the Blue and Red Indicator will blink.
The unit will start p video recording. Short press Button again to stop recording, the Blue and Red Indicator will stop blinking and illuminate. VGA Video Mode 1. The unit will be VGA standby Mode. Short press Button, the Blue Indicator will blink slowly. The unit will start VGA Video recording.
Short press again to stop recording, the Blue Indicator will blink as fast as before. Picture Mode. Enter VGA standby Mode as instructed earlier. Short Press Button, the Red Indicator will illuminate. The unit will be Picture Mode. Short Press Button once to take a picture.
The Red Indicator will blink one time. When it runs out of space on the memory card, the unit will automatically record over the oldest files by date. Dark Mode: 1. Power on the unit and enter any standby Mode as instructed earlier. Press and hold the Button for 3 seconds then release, the Red Indicator will blink two times then turn off. The Infrared LEDs will turn on. The video quality in dark environments will be improved. In Standby Mode press and hold the Button for 3 seconds then release again to turn off the Dark Mode, the Red Indicator will blink two times then turn off.
Motion Detection Mode: 1. Press and hold the Button for 2 seconds then release, the Red Indicator will blink. The unit will turn to Motion Detection Mode. Once the Lens detects any movement in front of the unit, It will start video recording till 1 minute after the movement stops, then it will be back to the Motion Detection Mode.
The Red Indicator will blink again. Short press any Buttons to exit Motion Detection Mode, the unit will stop video recording and back to video record standby Mode. The unit will automatically power on. The Blue Indicator will illuminate and the Red Indicator will keep blinking.
Wait a few moments, the storage folder for the unit will appear on the computer screen. Follow the on-screen instructions to watch, upload or save the files to the PC. Connect the unit to the computer as instructed earlier.
Open the storage folder on the computer. Save the changes of the TXT file then disconnect the unit to computer. Power on the unit. The time setting will be activated. You will find the desired time stamp on the left bottom of the video screen.
No comments:
Post a Comment